CNC or Mill machine shop in or REALLY close to spring?
Written by Josh on December 30, 2008 – 1:33 am -I 'm seeking a shop in or near 77,380 spring using machines similar to a compucarve (preferably to an industrial level) Read More →
Tags: Cnc Mill, Original Art, Thanks In Advance
Posted in FAQs | 1 Comment »
differences between acnc milling machine and a cnc machine center?
Written by Josh on December 27, 2008 – 7:01 am -Differences between the router and acnc of a CNC machine Read More →
Tags: Cnc Machine Center, Cnc Milling, Milling Machine
Posted in FAQs | 1 Comment »
Does anyone know where I can find out the limitations of an R8 milling machine spindle?
Written by Josh on December 26, 2008 – 1:21 pm -Most mills with the R8 Alberini not have no more than 3-4HP. Want to know how HP can be used on a machine with a post R8 instead of entry in the post NRC # 40. Read More →
Tags: Hp, Milling Machine, Spindles
Posted in FAQs | 1 Comment »
How to solve this equation?
Written by Josh on December 25, 2008 – 3:26 am -Calculate the horse power needed for energy source of a milling machine to produce a force of 5000lb interface between the cutter and the workpiece. The speed? Cutter? 450sfm and the relationship of power between the source and the interface? 2.1 - 1. Read More →
Tags: Interface, Power Ratio, Power Source
Posted in FAQs | 1 Comment »
i need help with two or three mah problems?
Written by Josh on December 24, 2008 – 4:33 am -1. Orders for the holding of the milling machine precision are fallen from 150 a year to123 next year. What? The percentage of decrease? 2. after an increase of 16%, the price of a pair of running shoes was $ 40.60. What was the price of old shoes. 3. the number of seats on the new airliner of Icarus 525? an increase of 36% over the old model. The new plane seats 374 passengers. How many passengers sitting on the old model has? 4.this year, realty Village has sold 289 homes. Last year, the realty has sold 340 homes. If sales fall next year by the same percentage, how many houses can? The realty invite the village to sell? Read More →
Tags: Airliner, New Plane, Old Model
Posted in FAQs | 3 Comments »
How do you eliminate backlash in a vertical milling machine?
Written by Josh on December 22, 2008 – 10:47 am -I 'go the VE tried that doesn' beyond the point I want to get to and then heading back it, but, the t seems to work. Council by some drivers with experience out there? Read More →
Tags: Backlash, Machinists, Vertical Milling Machine
Posted in FAQs | 2 Comments »
Electrical. 3-phase?
Written by Josh on December 21, 2008 – 8:06 am -What do I need to know if im connecting a milling machine (three phase) to the switch box. There are only two 3 tie leaving the car. I know black and red / blue. … is always hot and white is neutral. The tie will have worked through a conduit 3 / 4 of an inch to coat. all'interruttore hooked up. I want that something. Someone says to me is the three-phase connected cool … my memory …. Read More →
Tags: 3 Phase, Memory, Milling Machine
Posted in FAQs | 4 Comments »
How to loose weight?
Written by Josh on December 20, 2008 – 10:08 pm -I want to know the things I could do to remove more wieght. I TRED army on rolling mills and machines eleptical every other day for 40 minutes and I have lost a few inches, but weight. Furthermore path for about 30 minutes in addition to regular resolves the I listed before. I was wondering which foods to eat and what to stay to go. (is there any abdominal excercises that I can do to rid of my belly fat, it 's just in front of me all the way around or my sides. Read More →
Tags: 30 Minutes, Eleptical, Loose Weight
Posted in FAQs | 6 Comments »
Garage floor concrete strength?
Written by Josh on December 19, 2008 – 11:47 pm -The husband is planning on putting lle 7000 pounds. vertical milling machine on an area of 5 square ft attached to 4 points. The floor? about 5 inches of concrete floor of the garage often built in 1950. Read More →
Tags: Concrete Strength, Ft Square, Garage Floor
Posted in FAQs | 3 Comments »
Trying to find information on a candy making machine made by T. Mills & Bro. in Philadelphia pat. 1871?
Written by Josh on December 19, 2008 – 10:44 pm -We have a sweet make-made machine "T. The Macina & Bro. "Philadelphia, PA, patented Feb. 14, (18) 71. It consists of two cylinders engraved brass who once shot by the crank are drops of rubber or a type of candy Swedish fish. The machine is cast iron, appears to be chrome plated, has a hand along with a tot foot wooden handle to the periphery. I'm trying to find information on the types as well as that of the sweet material would be used in this machine. It wouldn 't hurt to know the value, one or the other. Read More →
Tags: Candy Machine, Philadelphia Pa, Wooden Handle
Posted in FAQs | 1 Comment »